How Long Does a Car Paint Job Take? What Happens at Each Step
How long does a car paint job take?
One U.S. estimate puts a full repaint at 40 to 80 hours of work. AAA gives a few days to a couple of weeks for the whole process. The time depends on the extent of the cosmetic damage, the size of the vehicle, the amount of prep work and any extra bodywork that the car needs.
Sources for this guide
Sources, as of 2026: AAA for the length of a paint job, the prep steps and what adds work; The Drive, a U.S. car repair guide, for the hours of work, rust and dent repair and the time paint needs to harden; I-CAR, the collision repair training organization, for infrared curing; a vehicle maker's paint handling guide for one of its models for cure and wax; and the procedures and data sheets of two paint makers for the steps and dry times. The hours and days are general estimates, and the dry times apply to one clear coat at the temperatures shown.
Hours of work versus days at the shop
The 40 to 80 hours are hours of work on the car, not days on the calendar. To turn them into days, divide by the hours that the shop puts into your car each day. For example, at 8 hours a day, 40 to 80 hours is 5 to 10 working days. At 4 hours a day, the same job is 10 to 20 working days. The days at the shop also include the dry time between steps, which the table below shows for one clear coat.
What happens at each step of a full repaint
- 1
Take parts off and sand
Parts such as the doors, trunk and hood come off, so that the whole car can be painted. The old paint is sanded.
- 2
Mask and clean
Areas that must not get paint, such as the windows, are taped off. The body is wiped down to remove debris.
- 3
Primer surfacer
From one paint maker's procedure
The primer surfacer goes on in coats. Each coat must flash completely (a drying pause between coats) before the next coat goes on.
- 4
Colour and clear coat
Clear coat figures from one product's data sheet
The colour goes on as a base coat. One refinish clear coat then goes on over it in 1.5 coats, with a flash of 0 to 3 minutes between coats at 21°C (70°F).
Spot repairs: hours of work and the prep before primer
At the low end of the same estimate, a spot repair is a few hours of work. For a light body repair, one paint maker's procedure lists this prep before primer: sand the repair area and 5 to 10 cm (2 to 4 in) past the damage, block-sand the body filler, let the glaze filler cure completely, then sand the featheredge, the tapered edge where the repair meets the old paint. When the repair passes a quality check, primer is next. For the hours of work on your own panel, ask the shop to list them in its written estimate.
Did you find what you were looking for?
Air dry, bake or infrared: how heat shortens the wait
Infrared (IR) lamps speed up curing and can greatly cut the time that a repair takes. The shop can also let the paint air dry, or bake it. Heat has limits: the clear coat in the table below must stay at or below about 50°C (120°F) on the part when it is baked, and at or below 60°C (140°F) under IR lamps.
Dry-to-handle times for one refinish clear coat (one paint maker's data sheet)
| Drying method | Temperature | Dry to handle |
|---|---|---|
| Air dry | 21°C (70°F) | 50 to 60 minutes |
| Bake | About 38 to 50°C (100 to 120°F) on the part | 20 to 25 minutes (dust free in 0 to 5 minutes) |
| Short-wave infrared lamp | About 38 to 50°C (100 to 120°F) on the part | 10 to 15 minutes |
| Short-wave infrared lamp | 60°C (140°F) on the part | 10 minutes |
Dry to handle versus cured paint
Dry to handle is not the same as cured. One vehicle maker says that the natural cure of the factory paint on one of its models can take up to 60 days, and that the paint must breathe in that time so that its solvents can escape. The same guide says to put no wax, sealant or other sealing product on that paint in the first 60 days after the car arrives. For the wait on a repaint, see the first question in the FAQ below.
What adds work to a paint job
- Rust. For a clean paint job, rust should be cut out or neutralized before any paint goes on.
- Dents. Dents are repaired before paint, because fixing them afterward could damage the new finish.
- Deeper sanding. Sanding can take off only the clear coat or go down to bare metal, and more prep can raise the labour cost.
- More coats. High-quality paints and special formulas often need multiple coats.
Cold, damp air and thick coats slow the drying
For the clear coat in the table, the dry time also depends on how thick the film is and on the air flow. One paint maker lists these causes of slow drying: spray conditions that are too cold, too little air flow in the spray booth or high humidity, and the wrong reducer (thinner) or hardener in the mix. It also warns against heavy coats (high film builds) and says not to apply urethane coatings below 13°C (55°F).
Related guides
- Understanding Supplements: Why Your Initial Repair Quote Might Change
Read it when the paint work is part of a collision repair and the first quote goes up.
- Matching Metallic Paint: Why Good Body Shops Blend More Than Colour
Read it when only some panels of a car with a metallic colour get new paint.
- Sustainable Collision Repair: What Waterborne Paint Really Changes
Read it if the shop paints with waterborne paint and you want to know what that means for your car.
Key Takeaways
- Infrared lamps can cut the cure time of primer too, not only of the clear coat.
- If more clear coat must go on after 24 hours, one clear coat's data sheet asks for sanding first, which adds a step.
- Before you book, ask a paint shop near you for a written estimate that gives the date your car will be ready.
Frequently Asked Questions
How long should I wait before washing a newly painted car?
Ask the shop that painted the car for its wait before the first wash and the first wax, in writing, for the paint that it used. Paint that feels dry still needs time to become fully hard. That is why add-ons such as a ceramic coating or a protective wrap often go on only well after the paint job is finished.
Does primer have to dry before the colour goes on?
Yes. In one paint maker's procedures, the primer surfacer air dries or is force dried for the time on its product data sheet, and only then is it sanded. A primer-sealer is ready for the colour coat once its recommended dry time is reached, so each primer layer adds its own wait.
How soon can new clear coat be buffed?
Straight away, when the clear coat was properly cured with infrared lamps: the painter can then sand and buff it. One clear coat's data sheet adds that the part must first cool to room temperature before anyone handles or polishes it.
Why is my car taking weeks at the body shop?
The workload of the body shop is one factor in how long a paint job takes, next to the work that the car itself needs, and a shop can take weeks. If the paint is part of a crash repair, see why a collision repair can run past its estimate.
Did this post answer your question?
Find trusted Auto Painting & Repainting shops near you
Compare local independent shops that offer Auto Painting & Repainting and choose the right fit for your vehicle.
Find Auto Painting & Repainting shopsShare or ask AI about this article
Continue the conversation or send this guide to someone who needs it.
Related guides
How Long Should You Wait Before Washing a Newly Painted Car?
When a newly painted car can go through a car wash, when to wax it, how to hand wash fresh paint, and what to do about bird droppings and sap.
Matte Car Paint: How to Care for It and Why It Is Hard to Repair
What a matte finish adds to the price of a car, how to hand wash it, what to keep off it, and why a scratch or chip means a panel repaint.
How to Restore Faded Car Paint: What You Can Fix and What Needs Repainting
Dull, oxidized paint can be polished and waxed at home. See which clear coat damage needs a repaint, and how to keep the paint from fading again.