Trusted Local AutoFind a Shop
Back to Blog
ADAS Calibration

How Long Does ADAS Calibration Take and What Happens During It?

informational·informational·

Where these times and steps come from

The steps and drive conditions come from technical articles by I-CAR, the non-profit collision repair training body, on vehicle preparation and on static and dynamic calibration (2019 to 2022), and from an I-CAR infographic that Fender Bender reported in 2022. The set-up time and the typical set-up list come from Body Shop Business (2022), the drive times from maker instructions that Repairer Driven News reported (2019), and the space guide from Vehicle Service Pros (2021). Only the range at the end of the answer above is a total time; the other times cover one step or one named vehicle. Facts as of 2026.

What shapes the length of the job

  • One method or two: a vehicle that needs both a static and a dynamic calibration goes through both sets of steps below.
  • The set-up: of all the work in a static calibration, putting the equipment in place takes the most time, and the exact measurements can add steps that the shop did not expect.
  • The vehicle itself: one calibration does not always take the same time, even on two cars that share the make, the model and the model year.

Did you find what you were looking for?

What happens during an ADAS calibration, step by step

  1. 1

    Prepare the floor

    The car is parked on a level floor, or on a floor with very little slope. Before the set-up starts, the area around the car is cleaned, and nothing is left on the floor near it.

  2. 2

    Set the fluids and the tire pressure

    In a typical static set-up, each fluid is brought to its recommended level, and the tire pressure is set to the value on the vehicle's tire placard.

  3. 3

    Place the frame and the targets (static)

    The technician puts the calibration frame in position and sets up the targets from precise measurements.

  4. 4

    Run the calibration on the scan tool (static)

    The technician starts the calibration software for the ADAS (advanced driver assistance systems) on the scan tool, the device that runs the calibration. In most cases, the calibration procedure for the vehicle lists the tools that the job needs.

  5. 5

    Drive the car (dynamic)

    If the procedure calls for a dynamic calibration, the car goes out on the road, and it is driven while the scan tool is connected.

  6. 6

    Test drive at the end

    The job ends with a test drive, after every calibration on the car is done, in the shop and on the road. Shops often keep it as a separate check, the last one before the car goes back to its owner.

Related guides

Key takeaways

  • Fill the fuel tank before you drop off the car: many calibrations need a full tank.
  • Take extra load out of the car before the appointment, because a typical static set-up calls for it to come out.
  • Ask a shop that does ADAS calibration for a time estimate for your exact vehicle, and for the time when it expects to return the car.

Frequently asked questions

Will an ADAS calibration put kilometres on my car?

It can, when the procedure includes a road drive. In 2019 instructions for Tesla's second-generation driver-assistance system, the calibration could take up to 160 km (100 mi) of manual driving, with a person at the wheel. The distance depended on the type and the condition of the road.

Why do two technicians take my car out for the calibration drive?

Because a dynamic calibration is often a job for two people. One technician drives the car. The other one rides along, follows the written procedure, tells the driver what each next step is and handles the scan tool for the whole drive.

Does weather affect an ADAS calibration?

It can affect the part of the job that happens on the road. Weather and the state of the road both play a part in a dynamic calibration. The maker's procedure can also set conditions for the drive, for example a speed, lane lines that are easy to see or a certain time of day.

Can a static ADAS calibration be done in any garage?

Only in one with enough level, open floor. Some vehicle makers set a distance of flat, open space that the car needs around it, and the technician should look it up in the service information before the work starts. As a general guide, many makers of aftermarket calibration systems suggested about 9 m by 14 m (30 ft by 45 ft) in 2021.

Did this post answer your question?

Find trusted ADAS Calibration shops near you

Compare local independent shops that offer ADAS Calibration and choose the right fit for your vehicle.

Find ADAS Calibration shops

Share or ask AI about this article

Continue the conversation or send this guide to someone who needs it.