Trusted Local AutoFind a Shop
Back to Blog
Bumper Repair & Replacement

Will a Cracked Bumper Fail a Safety Inspection? Canada and U.S. Rules

informational·informational·

Sources and the agencies to ask

Rules as of 2026 from the Ontario Ministry of Transportation (MTO): its Passenger / Light-Duty Vehicle Inspection Standard (Section 8, item 8: bumper) and its safety standards certificate page. Also British Columbia's Light Vehicle Inspection Manual (Section 8, item 5), Pennsylvania Code Title 67 (sections 175.80 and 175.220), and the Virginia State Police inspection rules in the Virginia Administrative Code (19VAC30-70-120). Bumper rules differ by province and state, so confirm the bumper item with your provincial or state inspection authority, or with the inspection station, before the test.

Bumper reject items in the MTO inspection standard

  • Missing or wrong part: the bumper is missing, modified, inferior to the original factory design in width, size or structural integrity, or incorrect for the vehicle.
  • Loose or broken mounting: the structure, the supporting structure or the fasteners are broken, misaligned, loose or missing.
  • Collapsed: the bumper is collapsed or inoperative.
  • Hazardous edge: any section has an exposed sharp edge, is torn, or sticks out in a way that could be hazardous to the driver, a passenger, a pedestrian or a cyclist.

How the reject items apply to a crack

A thin crack in the plastic cover; the cover is firm, and no edge is sharp or sticks out
Read against the list above, the crack by itself matches none of the reject items. A broken clip or bracket behind the crack is a separate reject item, so do the checks in the step list below before the test.
The crack has opened into a sharp edge, or a torn flap sticks out
This matches the hazardous-edge item: the standard treats such an edge as a hazard to pedestrians and cyclists, not only to the people in the car. Have the cover repaired or replaced before the test. Do not drive with a piece that hangs loose or drags; have it secured or removed first.
The cover moves, sags or pulls away at the crack, or clips and brackets are broken
This matches the item for broken, loose or missing fasteners and supporting structure. Have the clips or brackets replaced, then check that the cover sits firm.
The crack came from a collision, and the bumper now sits in or out of line
A misaligned or collapsed bumper is a reject item, whatever the crack looks like. This guide to collision damage explains how to tell frame damage from surface damage.

Did you find what you were looking for?

Do British Columbia, Pennsylvania and Virginia fail a cracked bumper?

Do British Columbia, Pennsylvania and Virginia fail a cracked bumper?
PlaceRule and authorityBumper faults that fail
British ColumbiaLight Vehicle Inspection Manual, Section 8, item 5 (provincial government manual)A missing, loose or broken bumper, or a torn portion that sticks out so as to create a hazard
PennsylvaniaPennsylvania Code Title 67, sections 175.220 and 175.80 (state inspection rules)A missing front or rear bumper (street rods are excluded), and torn metal, glass or other loose or dislocated parts that stick out from a surface of the vehicle so as to create a hazard
Virginia19VAC30-70-120 in the Virginia Administrative Code (state inspection rules)Body or bumper mounts or mounting hardware that do not properly secure the bumper to the frame as originally designed

When Ontario needs a safety standards certificate

In Ontario, you need a safety standard inspection and certificate when you transfer a used vehicle to a new owner (unless the new owner is your spouse), register a rebuilt vehicle, register a vehicle from another province, territory or country, or change a vehicle's status from unfit to fit. The certificate is valid for 36 calendar days after the inspection, and it is not a warranty of the vehicle's condition. The bumper is one item of many: see the full Ontario checklist for the others.

How to check a cracked bumper before the inspection

  1. 1
    Look in good light

    Ontario inspection procedures are visual unless the standard names another procedure. Look at the bumper from the front or rear and from each corner.

  2. 2
    Check the crack edges

    Look along the crack for a sharp edge or a torn flap that sticks out. Wear a glove or use a cloth; do not run a bare hand along a broken edge.

  3. 3
    Push gently on the cover

    Press near the crack and at each corner. If the cover moves, sags or rattles, look under the edges for broken or missing clips, fasteners or brackets.

  4. 4
    Compare the gaps

    Compare the gaps between the bumper and the fenders, lights and hood or trunk on each side. If one side sits higher, lower, in or out, the bumper may be misaligned or collapsed.

Repair or replace a cracked bumper before the test

Fix each fault before the test. Because the Ontario list rejects a modified bumper or one inferior to the original design, ask for a repair or a replacement part that keeps the original width, size and strength. For repair-or-replace prices, read about plastic bumper repair costs. If you need the certificate for a sale, book the inspection after the repair and close to the sale date, so that the certificate is still valid at the transfer.

Related inspection guides

Key Takeaways

  • The four rules in this guide list bumper faults, not cracks: in Ontario, a cracked bumper fails when it is also loose, broken, misaligned or collapsed, or has a sharp, torn or protruding edge.
  • A sharp edge or a piece that hangs loose is a hazard to pedestrians and cyclists, not only an inspection fault.
  • Before you book the inspection, ask a bumper repair shop to check the cover, clips, brackets and mounts and to give you a written estimate.

Frequently Asked Questions

Does a truck need a rear bumper to pass the Ontario safety inspection?

Only if it came with one. Ontario's standard requires bumpers on the front and rear of passenger cars, minivans and SUVs, and on the front of trucks. A rear bumper is required on a truck if the truck was originally equipped with one, unless it was removed to install other equipment.

Does a rusted bumper fail inspection?

It fails in Ontario when the rust has made a hole: the standard rejects a bumper with any perforation due to corrosion. British Columbia's inspection manual rejects a bumper that is perforated through. Check the mounts and brackets for rust as well, because a broken or loose mounting is a separate reject item in Ontario.

Can a damaged bumper absorber fail inspection?

Yes. British Columbia's Light Vehicle Inspection Manual lists the bumper shock or impact absorber as its own item, next to the condition of the bumper. An absorber that is collapsed, welded to the rail, solid or not collapsible is a reject item, even when the bumper cover has no damage.

Can I use zip ties or tape on a cracked bumper to pass inspection?

Not while the fault is still there. Ontario's standard rejects broken, loose or missing fasteners, a modified bumper, and a section that is torn or protrudes. Tape or zip ties over a broken clip leave the clip broken, and a cover that still moves or an edge that still sticks out matches those reject items.

How much does a safety inspection cost in Ontario?

It depends on the station. The cost of the safety standard inspection and the certificate is different at each Motor Vehicle Inspection Station, so ask two or three stations for their price when you book. If the car fails on the bumper, the repair cost comes on top of the inspection fee.

Did this post answer your question?

Find trusted Bumper Repair & Replacement shops near you

Compare local independent shops that offer Bumper Repair & Replacement and choose the right fit for your vehicle.

Find Bumper Repair & Replacement shops

Share or ask AI about this article

Continue the conversation or send this guide to someone who needs it.