What Is Frame Straightening and How Does a Body Shop Do It?
What is frame straightening?
Frame straightening is the collision repair work that pulls a bent frame or unibody back to the vehicle maker's specifications. A body shop measures the damage in three dimensions, sets the car up on a frame rack or bench and anchors it, pulls the bent areas, then measures again. Parts that the maker does not allow to be straightened are replaced instead.
Sources for this guide, as of 2026
This guide draws on collision repair guidance from I-CAR, a non-profit training and research body, including vehicle maker positions that I-CAR publishes; the structural repair rules of the Société de l'assurance automobile du Québec (SAAQ); a 2020 ICBC notice for its Collision Repair Program in British Columbia; and vehicle type definitions from AAA Club Alliance. Some heat and steel limits come from single vehicle makers, so the repair information for your own car decides.
Body-on-frame or unibody: what "frame" means on your vehicle
| Build type | How the body and frame are made |
|---|---|
| Body-on-frame (an SUV, for example) | Two pieces: a separate frame, with the body joined to it during manufacturing |
| Unibody (a crossover, for example) | One piece: the body and the frame are built together |
How a body shop straightens a frame, step by step
- 1Measure the damage in 3D
The technician measures the structure in three dimensions and compares the readings with the vehicle maker's specifications.
- 2Set up and anchor the car
The car goes onto a frame rack or bench and is anchored there before the pulls start.
- 3Pull the bent areas
The technician pulls the bent parts of the structure back into line.
- 4Measure again
After the pulls, the shop measures the structure again and compares the new readings with the first ones.
Did you find what you were looking for?
Can you straighten a frame yourself with a kit?
No, not a frame or unibody that was bent in a crash. Three-dimensional measuring before and after the pulls gives an accurate assessment of the damage and records the result. In British Columbia, shops in the ICBC Collision Repair Program must have electronic equipment that measures length, width and height at the same time and reads the underbody while the car is set up on a frame rack or bench.
Straighten or replace: how the shop decides
Maker repair information and certified shops
Collision repair trainers tell shops to always use the maker's repair information to see how the body is built and which parts can be repaired. In Quebec, a shop must check that the vehicle maker authorizes a structural repair before it starts. When a maker gives its repair instructions only to shops that it certifies, as some luxury makers do, Quebec requires structural repairs on that make to be done by one of those shops. See what changes between certified and non-certified collision repair shops.
Related guides
- Frame Repair vs Cosmetic Damage: How Serious Is Your Collision?
Read this first if you are not sure that the crash reached the structure.
- Why Aluminum Collision Repair Needs the Right Tools, Training, and Space
Read this if your vehicle has an aluminum body or aluminum structural parts.
- How Potholes Cause Hidden Structural Damage to Your Car
Read this if the impact was a pothole or a curb, not a collision.
Key Takeaways
- Straightening and replacement go together: the maker's repair information decides which damaged parts are pulled and which are replaced.
- A body-on-frame vehicle and a unibody go through the same order of work: measure, anchor, pull, then measure again.
- Ask a frame straightening shop for a written estimate that lists which damaged parts it will straighten and which it will replace.
Frequently Asked Questions
Can a shop use heat to straighten a frame?
Not on structural parts in Quebec: the rules there prohibit heat for straightening them. Some vehicle makers also forbid heating load-bearing parts to make them easier to reshape. Where a repair does use heat, the shop must follow the vehicle maker's heat procedures and recommendations.
Does a body shop print the frame measurements before and after the repair?
In British Columbia, shops in the ICBC Collision Repair Program must use electronic measuring equipment that prints reports from before and after the repair. The same equipment must also be able to confirm the alignment of the entire vehicle structure.
Does frame straightening need special training?
Yes. Straightening a structure that was bent in a crash is skilled work, and no single routine suits every kind of damage, so the technician must judge each repair. Collision repair trainers run separate video courses on measuring, anchoring and pulling for full-frame and unibody vehicles.
Can a shop cut out the bent section and join in a new one?
Only when the vehicle maker publishes a sectioning procedure for that part. Sectioning means the shop cuts out the damaged section and joins in a new piece instead of straightening it. When the maker has no published sectioning procedure, collision repair guidance says the shop must not section.
Did this post answer your question?
Find trusted Frame Straightening shops near you
Compare local independent shops that offer Frame Straightening and choose the right fit for your vehicle.
Find Frame Straightening shopsShare or ask AI about this article
Continue the conversation or send this guide to someone who needs it.
Related guides
How to Check a Used Car for Frame Damage Before You Buy
A buyer's checklist for frame damage: what to check on the lot and the test drive, what history reports and dealers must show, and who should inspect the car.
Ontario Structural Inspection Certificate: What It Is and When You Need One
What Ontario's Structural Inspection Certificate is, which vehicles need one, who issues it, what it checks, the cost rules and how Salvage becomes Rebuilt.
Does Frame Damage Mean Your Car Is a Total Loss?
Frame damage does not always total a car. See how insurers weigh repair cost against value, U.S. state percentages, and salvage and rebuilt rules in Canada.